<samp id="trema"><em id="trema"></em></samp>
<samp id="trema"></samp>
<sup id="trema"></sup>
<sup id="trema"></sup><sup id="trema"></sup>
<sup id="trema"></sup>
<delect id="trema"><noframes id="trema"><samp id="trema"><em id="trema"><blockquote id="trema"></blockquote></em></samp>
<samp id="trema"><em id="trema"><blockquote id="trema"></blockquote></em></samp>
 
 
產品中心
道康寧熱塑性彈性體TPE TPR
A4001 50A(道康寧熱塑性彈性體TPE TPR)

關鍵詞:A4001 50A,TPSIV,熱塑彈性體
MULTIFLEX&reg; A 4001 50 A NAT 59150

Compatibility / 結合材料: ABS/ASA/SAN/PMMA/PC/PETg/PS/HIPS 

Process / 加工: Injection/Extrusion, 注塑/擠塑

Other information/其它信息: EN71-3 met/符合EN71-3標準;FDA met/符合FDA標準   

PROPERTIES / 性能UNITS / 單位STANDARDS / 標準Average Values / 平均值
Hardness 硬度Shore A 邵氏 AISO 868 - MDA 110  50
Density 密度g/cm3 克/厘米3ISO R1183 - MDA 1121.03
Spiral flow 螺旋注塑長度Cm /厘米MD17956
Tensile strength at 100% elongation
100%伸長率時的抗拉強度
Flow Direction 縱向
Transverse Direction 橫向
MPa 兆帕ISO 37 - MDA 121--
Tensile strength at 200% elongation
200%伸長率時的抗拉強度
Flow Direction 縱向
Transverse Direction 橫向
MPa 兆帕ISO 37 - MDA 121--
Tensile strength at 300% elongation
300%伸長率時的抗拉強度
Flow Direction 縱向

Transverse Direction 

橫向

MPa 兆帕ISO 37 - MDA 121--
Tensile strength at break
斷裂時的抗拉強度
Flow Direction 縱向
Transverse Direction 橫向
MPa 兆帕ISO 37 - MDA 1213.5
2.5

Elongation at break
斷裂時的伸長率
Flow Direction 縱向
Transverse Direction 橫向

%ISO 37 - MDA 121

>500                                     

>500


Tear Strength 抗撕裂強度
Flow Direction 縱向
Transverse Direction 橫向

KN/m&sup2;
千牛頓/米2
ISO 34  - MDA 12123.0
15.0

The MDA (Méthode D’Analyse) named in this document are issued from the ISO Standards. 表中所提及的 MDA (Méthode D’Analyse) 是由 ISO 頒布的標準。  
The values mentioned in this Technical Data Sheet are issued from test bars realized on specific equipment, in conformity with normalized standards. Although we estimate that these information are exact, it is important to know that under other conditions with another equipment than our, the results can be appreciably different.

Therefore we are not responsible when those information are not interpreted as they should be.

產品規格中所列的各項數據是由特別的儀器遵照標準化測試所得到的。 盡管我們認為這些信息是準確的, 但是如果在其它的情況下由其它的儀器所測得的數據可能有所不同, 所以, 客戶應該自行確認產品可否被采用。

Dow Corning Corporation  

產品加工指南(注塑) / PRODUCT MOLDING GUIDE
                  MULTIFLEX&reg; A 4001 50 A NAT 59150


§Temperature Profile / 加工溫度:

REAR 后段CENTER 中段FRONT 前段NOZZLE 射嘴MOLD 模具
165°C175°C180°C185°C30°C


* All temperature at +/-10 °C, 所有加工溫度可以在正負10攝氏度之間調節

§Predrying advice / 干燥建議 : 

Temperature 溫度Time時間
60°C2 hours/小時



§Injection speed / 注塑速度 :    Middle to High / 中 至 快速

§Injection  and back pressure / 注塑壓力和背壓 :

Injection pressure 注塑壓力Back pressure 背壓
30-80 Bar3-20 Bar


§ Cooling time / 冷卻時間 :
5-15 second / 5-15 秒


§ Coloring Masterbatch/Pigment Powder selection / 色母粒/色粉選擇建議 :
We recommend using pigment powder or EVA based coloring masterbatch. Please avoid using PE or PP based coloring masterbatch.
我們建議在該材料的配色過程中使用色粉,或者使用以EVA為載體的色母粒。請在配色過程中盡量避免使用PE或PP為載體的色母粒,以免影響材料和工程塑料之間的粘合能力。

 

 
天天射天天操天天干_国产精品人人做人人爽人人添_天天色天天干天天_中文字幕天天躁日日躁狠狠躁免费_人妻另类无码视频_AV在线入口观看